ASTM B – Designation: B /B M – 01 Standard Speci?cation for Copper -Nickel-Tin Alloy, C. This standard is issued under the fixed designation B /B M; the number . ASTM designation and year of issue (B/. B M. ASTM B attains the requirements for copper-nickel alloy plates, sheets, strips, and rolled bars made from UNS C, UNS C alloy. Such Sheet or.
|Published (Last):||23 January 2005|
|PDF File Size:||18.26 Mb|
|ePub File Size:||17.29 Mb|
|Price:||Free* [*Free Regsitration Required]|
C and C M20 H01 H02 H04 H06 H08 as hot-rolled quarter hard half hard hard extra hard spring 45 58 66 75 80 84       65 72 80 88 92 94       Grain Axtm for Annealed Tempers 9.
Within the text, SI units are shown in brackets.
Siddhagiri Metals and Tubes Aatm This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? C 5 70 Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Combining values from the two systems may result in nonconformance with the speci?
The ingot is soaked at the hot rolling temperature and then rolled into blooms or billets or slabs. Such Sheet or Plate is manufactured by hot or cold working, and annealed if required in order to produce a uniform wrought structure to meets the specified temper properties. A billet is rolled out of bloom, has at least 40 mm X 40 mm cross-section.
ASTM 1b22 not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. When all the elements in Table 1 are analyzed, their sum shall be as follows: Grain size is the standard requirement for all products in the annealed tempers.
Cupro Nickel (UNS C, ASTM B)
Looking for some more information? B Scale 68—82 80—90 87—94 89—96 Super? Steel ingot is the cast metal with porosity and blow-holes.
Last previous edition B — Workmanship, Finish and Appearance It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
ASTM B Copper Nickel Sheet Plate Supplier · B C/C
C M20 H01 H02 H04 H06 H08 as hot-rolled quarter hard half hard hard extra hard spring 38 47 56 67 72 76       56 63 70 79 84 87       D Silicon and titanium each at 0.
The following alloys are covered:. Each product should be manufactured by hot or cold working, and annealed if required, to produce a uniform wrought structure that meets the specified temper properties.
The second is the electric arc furnace Sstmwhich primarily uses steel scrap as the raw material. NOTE 2—Because of the discontinuous nature of asym processing of castings into wrought products, it is not always practical to identify a speci?
A asstm, also from ingot, has a rectangular cross-section, with an area of at least cm2 and width at least three times the thickness. C M20 H01 H02 H04 H06 H08 as hot-rolled quarter hard half hard hard extra hard spring 42 55 58 71 73 78       62 67 72 85 90 91       C 48 55 63 73 79      63 70 77 87 91      If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
C M20 H01 as hot-rolled quarter hard 52  58  65  72  There are two sstm production streams that is used to produce rolled bar products. This abstract is a brief summary of the referenced standard.
70-30 Cupro Nickel
The derived SI unit for force is the newton Nwhich is de? C 2 65 18 C, C, C, C, and C for use as tube plates in surface condensers and heat exchangers are covered by Speci?
C M20 H01 H02 H04 H06 H08 as hot-rolled hard half hard hard extra hard spring 48 56 67 ast, 89 95       65  73  82  94